How to Replace a Kia Sportage Replacement Key
The key of a lot of Kia models has the keyless entry feature built in. This key usually resembles an remote control, and can be exchanged with a fresh one from an Kia dealer or locksmith.
Key fobs can fail to function due to a number of reasons, including an inactive battery, worn out buttons, signal interference or water damage. Here are some guidelines on how you can get your Kia Sportage replacement key to function again.
How to replace a smartkey or remote key?
The battery inside your Kia's smart key will eventually need be replaced, whether it's a remote key, a push-to-start key or a regular metal key that doesn't contain a transponder. This is especially when the car displays a message telling that the smart key or remote has a low battery.
This is a relatively simple process. To replace the keyfob battery remove your mechanical key from the slit that is located at the back of the fob. Then, pull the cover off. Inside the key fob there will be a small screw that holds the battery in its place. Using a small screwdriver, take the screw off and pull out the old battery. Install the new battery and close the slit on the key fob.
When the key fob is equipped with new batteries Test it by pressing the locks and unlock buttons. It's good in case the doors lock and unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to do some errands in Brandon.
Note: Some key fobs might need to be programmed (transponder chips or smart keys). This requires a machine for programming which is available to the locksmith who works for the automotive dealer. Other keys (non-transponder metal keys) don't require programming. If you need to reprogramme your key, you'll need to record the key code number on the key code tag.
How do you replace a battery?
If your Kia key fob isn't responding when you press the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A weak battery can cause other issues such as the check engine light coming on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a fairly simple DIY task that requires only a few tools.
Before you begin the process ensure that your vehicle is off and that all doors are shut. Find the small metal or a plastic piece that is located at the bottom of the key fob. Then, jiggle it until the key comes out. Then, you can put the key into the handle of the door for the driver to open your car.
To replace the battery on the key fob, you must remove the rear cover. Make use of a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery and align the new one in a way that the "+" positive side is facing you and the "negative" negative side is facing towards the fob's electronic contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damage or bending the metal contacts.
After you have installed the new battery then turn the key fob off and on in the ignition until the door locks up. You can then test your Kia's key fob again to make sure it's working as intended.
How to replace the smart key
Depending on the model of the Kia Sportage, you may have a standard key fob or a smart key. The smart key comes with an embedded mechanical key blade, however, the standard key fob does not. Both key fobs have a battery that will eventually need to be changed. It's quite simple and takes only two minutes.
Before you start before you begin, ensure that you're on a flat surface with good lighting and that your Kia is turned off. Keep in mind that there are small parts inside the fob that could be snagged if not vigilant.
The release button for the small size is located on the lower backside. This will either be an oval silver button or a rectangular slot. When you press it button, the mechanical blade will pop out and you can then open the key fob.
After the key fob has been removed, you can remove the old battery. The new battery is CR-2032, and can be bought on the internet or at your local auto parts store. When you're done, the key fob should permit you to lock and unlock your vehicle, even if it isn't running.
How to replace a mechanical key
The Kia keyfob is an excellent convenience, allowing us to lock or unlock our car by pressing the button. But, as with all devices there are issues with it from time to time. There are ways to fix these problems and keep your key fobs running for the duration of.
A low or dead battery is among the most common problems. This could cause the fob to stop working altogether or work intermittently. If The Keylab is the issue you should replace the battery an entirely new battery.
If this doesn't fix the issue you can try using a standard flathead screwdriver to open the fob's plastic casing. Be careful not to damage any internal components, or scratch the plastic. After the battery has been removed then replace it with a brand new one.
Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key which will fit into the slot). Test the key fob and verify that it's working correctly. If the key fob isn't working, contact an authorized locksmith or dealer to help resolve the issue. Make sure they make you an emergency key that functions for all trunk and door cylinders to avoid future lockouts.